Just a nice B/W shot to start with:


Removed the spare-tools lids. was quite tricky because i had to cut new Slots to get the screws out:


and out they are:


Removed a bit of those insulation mats with a rubber hammer on the driver side in the trunk. benefits of having a unheated (read: Freezy) garage is that tar-mats tend to get brittly


Next up was some interieur stuff behind the rear seat:




and at this point i found my first serious rust-hole:


at this point i decided to spend the rest of my time removing the brittly old bad paintjob with a spatula. Totally useless becase car will get a sandblast / Sanding anyway if i decide to use this shell, but just so much fun:

i like the first pics w&b nice work

_________________
paint by Mother Nature!
join!
http://www.facebook.com/pages/Kamikaze- ... 0425072482

thanks mate, you also might like this one from the first Z then

Long time no update. I‘ve been busy making some extra space in the garage and clean up the mess there Also I removed a lot of paint and thought it wouldn’t make sense to post pictures of every bit of junk I removed so far
This is how it looks on the outside currently, lot of paint removed just for fun:


Lots of surface rust underneath. anyway i continued with removing some of the insulation in the trunk:


next on the list was get out the interieur behind the seats and look how the structure is underneath:








Found a big hole on the passenger side rear inner wheel well:


Now after i've seen a few things on the black car i feel like i have a plan again:
The white (first car) seems to have better base structures, so at the moment i think i'll go with the white car. If the front end of the black one is good (on the white it isn't, also due to a lot of bad repair-attempts) i'll use the entire front-end of the black car. So Disassembly of the black car's front end is what's up next:


more to come on the front-end
In the meanwhile it got pretty freezy in the garage again and i feel a bit sorry for the white shell sitting outside in the cold, will put it back into the garage soon, or find another home while i work on the black car:


Then i had a few dollars left on my paypal account last month so i thought this is a good excuse to buy some small parts from MSA (zcarparts): Got a set of NOS rear pillar emblems as well as a hood emblem:

It's currently -3°C in the garage (26.6°F) in the garage, but some good work keeps me warm Started disassembly of the front end today, t his will alow me to remove the fenders to check the structure of the chassis in the front.
1) Removed the front-bumper with the swiss-spec Corner lights. It's slightly dented but repairable.


here it's gone:


2) next was the front lower panel, it's quite bent but usable:


next on the list was the grille, but i wasn't able to remove all the screws so i let them soak in some WD40 for a while While working i found the VIN-tag plate:


and noticed a weird thing: Even if both cars are 1972 Swiss-spec cars they have different oil filler caps. here's the one i found in the black car:


and here the "elephant" type oil filler cap from the white one. Of course i'll go with this one

I really need to build one from a bare shell like this some day...

Keep up the good work!

Been cool in Sydney too, @ 27 degrees C
Usually well into the 30s this time of year.
Looks like you're having fun though.

_________________
This space intentionally left blank.

Sorry for the lack of updates. Pre-christmas stuff keeps me busy currently, but soon Christmas holiday is coming so i hope to be able to get a few things sorted.
Compared the damage on my two chassis today. Still need to check a few things but this is what i saw so far:


So my plan is to do the same as Torby from Latenightgarage to his Z. Swap the entire front end from my black car to the white one, as well as the taillight surrounding. still need to study a lot of things but this seems a pretty nice way to make one good Chassis out of two rusty ones as the front is pretty well on the black one but the restunusable and the front-end is the biggest problem (with a lot of cheap repair patches) on the white one:

I like your plan, but you need to build a jig to make sure the chassis mate correctly. It would be quite embarrassing to have a Z with a droopy or upturned nose.

yeah that's the plan, im in contact with torby who did the same (see picture above), im sure he'll have some good advice and at the end i won't do it on my own but the bodyshop will do the work for me

nice project i dig that leather lining on the interior, never seen that before.

thanks mate Think this was standard interieur on european models

Oh man, what a great thread. Spent the entire evening reading it, keep up the good work!

_________________
'90 N13 Sunny 1.6 GT - '00 P11-144 Primera 1.8 - '03 K12 Micra 1.2

Glad to see some updates, I was starting to miss this build!

_________________
-Cam
1980 Toyota Celica
1984 Porsche 911
1988 Mazda RX7

Thanks guys - yeah i miss updates too
But i have some stuff coming soon and hopefully i find some time to get some work done soon too.. really sucks to have two Z's laying around and no time to work on them...

hahaha, I want your problems.

_________________
-Cam
1980 Toyota Celica
1984 Porsche 911
1988 Mazda RX7

Haha yeah - first world problems, i know
At least my EK9 Project is coming along so that "time-consumer" should be done by next summer and then full time on the Z's - well we'll see

I'm in the same boat, though...it's far too cold to be able to work on any of my toys. Can't wait for springtime.

_________________
-Cam
1980 Toyota Celica
1984 Porsche 911
1988 Mazda RX7

Spent another hour at the new (black) Z and "freed" the front end to have a closer look:
1) Grille off:


2) Fenders off:




3) Hood off:




Good news: I found what i was looking for: A pretty solid, straight and not-too-rusty Front end. Perfect for swapping it over to the white chassis

Awesome! Have you found a shop to do the transplant yet?

_________________
-Cam
1980 Toyota Celica
1984 Porsche 911
1988 Mazda RX7