hey guys, im a new member.
from auckland, always had 323s, this is one of about 6 ive owned, this was my second one, and only rotary converted one ive owned, had it for about 5 years, since i was 17 years old.
fell in loev with it the first day i saw it.

79' 323 wagon
sprayed in yellow, blacked out upohestery, everythings black and original, am radio, (amp under seat which runs one 4" speaker in teh standard hole in the dash with ipod cord so all is hidden)
GSII rx3 savannah coupe steering wheel
13x7 mogulars with 215 50 13 white writing yokohamas
13b bridgeport s4 non turbo block
mx5 gearbox
b2000 lsd diff
hardy spicer custon made driveshaft to suit
fully adjustable 1 off front struts
rear leaf spring, about to upgrade to ultra heavy duty rear shock out of VS commadore so nice and stiff

When i first got it it was low on some dirty mods, it was pretty fucking ruff, the guy i bought it off got it like this
he ended up just treating it like shit so it was kinda ruff when i bought it. wish i had restored it to its former glory, but hey, i was young!






Im currently decideing weather to chop the modgies out to 13x11's on the read and 13x10's up front, because i have to run a 1" spacer to fit around the coil overs, the will sit flush, and run 175 50 tires so they will majorly stretched, or use 175 50 and do a little stretch on these wheels
they will space out nicely, but still undecieded.

opinions welcome!

А не подскажите какое растояние между болтами на ступице на этой машине?

If i translate correct here is the answer

the gold wheels are 4x114
my car is 4x110 on the rear, and because i have s3 front hubs they are 4x114 up front .

Thank you very much

I like drift.How do you think motor of my car Will cope with these load?

this doesnt make sense brother!

I did have this photo as the inspiration for mine for a while till I went a different direction.

Your wagon is going to look awesome on those rims too. How did you do the S3 front end conversion? Is it the same as the S2, but with different hubs? I was considering this to get a better selection of wheels

Hey dude, i got a factory set of s3 struts, then re vamped them, cut off spring seats, and got the weld on adjustable sleeves with cusco adjustable camber top hats, with the new shock i used a seris 2-3 shock, s1 shocks are 1" longer, but the 2 and the 3 series are that 1inch shorter, so its all set up to have tonnnnes of clearance.
im just having trouble finding a s3 caliper re-build kit, any ideas? Im SICK of dealing with mazda, every time ive ever spoken to them, they flog me off as the car is old, and they are simply lazy.
anyway, s3 brakes are the biggest of the rx7 brakes that came with the factory 13" wheels, i was lookin at some willwood calipers, but they were going to end up being way too expensive, and lets face it, brand new s3 stuff will be efficient enough.
Wheel fitment wise, with the front im going to run a 25mm spacer, and the rear will have a 25mm adaptor.

how much do modgies wheels cost ruffly

Modgies are cheap, advanti do them for around $780

brand new

http://www.trademe.co.nz/motors/car-par ... 421878.htm

man those hd wheels are awesome, where might one find a set of those?
are for what sort of figure?

_________________
bog standard 1977 323 bugeye
1971 alfa 1750 gtv project
1981 Datsun 1200 Ute

Hey dude, those wheels are super cheap, im getttin them for $800. Two hunhdy a wheel is a bargain. 0 offset too

the wholesaler is www.yhi.co.nz but i cant see them on there site, im going trhough a friend at firestone, and thats the wholesaler there.

there by hd racing, the model is called 'rsb'.

i saw they were branded konig on another site, but here they are branded in this auction as advanti.
i dont know how it works re naming stuff but yeah

http://www.trademe.co.nz/motors/car-par ... 439936.htm

and there 13x7
not 13x6

i dunno why this auction says 13x6 because they dont make them in 6s

Nice I'll have to keep an eye out for some over here in QLD
they would look great on my ute.

Bruce

_________________
bog standard 1977 323 bugeye
1971 alfa 1750 gtv project
1981 Datsun 1200 Ute

Yep the new wheels look about 4 million times better than the modgies.
Nice little wagon.

_________________
http://www.ausrotary.com/viewtopic.php?f=7&t=152986

My Videos
http://www.youtube.com/restoremaz

Tried them on last night, they looked great.
25 offset rules!
Only two sets in the country, apparently nobodys bought them, very un popular i suppose, lost my job this morning so have them waiting for when i come up with some dollars!
ill post some pix up of them when there all on with rubber.

sweet wagz bro

_________________
PULSIFIER

Hey mate,
Do you have Repco in NZ? If yes, then ask them about brake rebuild kits for your brakes.

I got complete caliper rebuild kits for my S2 RX7 brakes from them.