Page 1 of 3 123 LastLast
Results 1 to 10 of 23

Thread: ssr mk iii 15x10 -24 refinished

  1. #1
    Member
    Join Date
    Oct 2009
    Location
    westminster
    Posts
    31

    ssr mk iii 15x10 -24 refinished

    This is the third wheel that I have tested. If you notice there are 16 bolts instead of the traditional 6, 8, 12 depending on the year. Most of the SSR Techno series if not all are welded 3pc. Because they are welded the bolts were use just for aesthetic reasons. Well after testing a few, I have decided to make them with 16 since this is the minimum amount that can be used without any failure. I could of done 12 but didn't want to test the limits. Now I can do them in 8 bolts but that would mean I would have to weld the wheel up like the original specs. The way I chose would allow the wheels to be true modular. BTW, these use to be 14x6.5 +12




  2. #2
    Administrator JNC's Avatar
    Join Date
    Mar 2007
    Location
    Socal
    Posts
    1,645
    wow are you doing these yourself??? you have a shop or?
    -Matt

  3. #3
    Member
    Join Date
    Oct 2009
    Location
    westminster
    Posts
    31
    I design and figure out the ins and outs then out source it.

  4. #4
    Member
    Join Date
    Oct 2009
    Location
    westminster
    Posts
    31
    waht do you think about the 16 bolts? too many or worth the mod to make them safe and modular

  5. #5
    Senior Member
    Join Date
    May 2008
    Location
    Northern California
    Posts
    635
    Quote Originally Posted by dimsum
    waht do you think about the 16 bolts? too many or worth the mod to make them safe and modular
    Wheels look real nice :tu: Do you have pictures of the before & after?

  6. #6
    Member
    Join Date
    Oct 2009
    Location
    westminster
    Posts
    31
    this is the original 14x6.6 +20


  7. #7
    Junior Member
    Join Date
    Sep 2010
    Location
    Belgium
    Posts
    21
    bad ass!!!

  8. #8
    Senior Member
    Join Date
    May 2008
    Location
    Northern California
    Posts
    635
    Quote Originally Posted by ¤gregzilla¤
    bad ass!!!
    I agree. So do you do this for a living?

  9. #9
    Member
    Join Date
    Oct 2009
    Location
    westminster
    Posts
    31
    do it as a hobby with a little money on the side. I run epicbmx.com for a living

  10. #10
    Senior Member
    Join Date
    Oct 2009
    Location
    Monterey Park ,Ca
    Posts
    119
    Who's making the barrels? Nice job by the way. The 16 bolts look way better than just 8 or 12.

Similar Threads

  1. SOLD Refinished 14x7 -9mm turbines 4x114.3 Oregon $400
    By ae86andkp61 in forum Wheels Swap Meet
    Replies: 4
    Last Post: 02-21-2014, 05:14 AM
  2. My l28ET 240z on refinished Hayashi 503's!
    By Sdgoods in forum Datsun/Nissan Garage
    Replies: 14
    Last Post: 06-24-2013, 03:29 AM
  3. 215 on 15x10
    By Johnnyboy110 in forum Resto Tips, Wheels & Other Goodies
    Replies: 2
    Last Post: 02-23-2012, 06:28 PM
  4. Advan A3A 14x9 0 offset refinished
    By dimsum in forum Wheels Swap Meet
    Replies: 6
    Last Post: 07-26-2011, 01:17 AM
  5. Refinished my wheels
    By Justin in forum Honda Garage
    Replies: 2
    Last Post: 06-19-2010, 12:16 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •